Products

RF Interconnects Filtre

RF Interconnects

  • The 2.92mm connector was developed for use to 40 GHz. The male pin is shorter than that of an SMA or 3.5mm to ensure that the outer contacts of the male and female connectors engage before the pin and female receptacle do. This ensures that the pin and socket will not see excessive wear and mating stress seen by misalignment in an SMA or 3.5mm connector. The 2.92mm connector also has a thicker wall than a standard SMA. The 2.92mm series mates with SMA and 3.5mm connectors.
    More
  • Enables design engineers to convert most existing RF antennas into Blind mate "plug in and forget" quick release antennas, which can be quickly installed and removed from platforms without having to connect or disconnect the coaxial cable. By simply adding a screw-on alignment sleeve, an existing antenna is converted into a plug in device. The interconnecting coaxial connector is fitted with a mating MNC connector which is permanently attached to the aircraft structure via a spring loaded receiver sleeve
    More
  • Government designation BMA (Blindmate A) was developed in the 1980's. The originally designated OSP™ connector by M/A-Com has excellent electrical performance up to 22 GHz in a compact size. SV Microwave offers extended frequencies on most BMA connector designs up to 26.5 GHz. With a slide-on interface and a connector durability of 5000 cycles, the BMA blindmate is suitable for high performance microwave applications.
    More
  • BMMA connector is a subminiature version of the BMA blindmate series. This originally designated OSSP™ connector by M/A-Com has excellent electrical performance at high frequencies up to 28 GHz. There is a complete family of BMMA blindmate connectors and adapters. BMMA connectors are approximately 25% smaller than the BMAs, and are used for applications where space is limited and no special tooling is required.
    More
  • The BMZ is government designation (Blindmate Z). This connector has low insertion forces and a light spring which allow for high density applications. The BMZ is a miniaturized version of the BZ, a high-frequency connector with slide-on mating. This blindmate has a frequency range of DC-18 GHz and 50 ohms impedance with an interface controlled by MIL-STD-348.
    More
  • Developed as a miniature version of the Type C connector, the BNC connector is a miniature quick mating and de-mating RF connector. It features two bayonet lugs on the female connector; mating is achieved with only a quarter turn of the coupling nut. SV Microwave's 50 Ohms BNC series connectors are miniature and lightweight. They are designed to operate at a frequency of DC to 11 GHz and typically yield low reflection through 4 GHz.
    More
  • The BZ connector is a high-power blindmate connector with slide-on mating. This originally designated PMA blindmate by Automatic has PTFE dielectric interface, telescoping insulators and wiping outer contacts. BZ blindmate connector applications include GPS navigation systems and antenna connections. The BZ blindmate connector is a mechanically ruggedized blindmate and can handle 6.7 KW to 2 GHz.
    More
  • SV Microwave manufactures a large variety of solderless precision RF connectors in high frequency bands including the mmWave frequencies. SV offers a variety of cost effective coaxial PCB mount SMA, 2.92mm and 2.4mm connector series. Our solderless application makes assembly fast, easy and without damaging the PCB board. Additionally, SV can customize a PCB footprint design for your application using our latest simulation technology. SV’s line of compression mount coax connectors are available in stripline and CPW/Microstrip options and are ideal for mobile communications (including 4G & 5G applications), wireless test and measurement, high speed digital environments, and much more.
    More
  • SV Microwave is the ONLY DLA approved source for these 2.92mm attenuators (DC through 32 GHz). SV's line has the precision, quality and performance unmatched in the marketplace . Our dB values range from 0.5 to 30 dB with low VSWR and flat attenuation. Available in screened and non-screened versions.
    More
  • SV offers a wide range of multiport connectors and cable assemblies. SV's precision and expertise enables our ability to manufacture high-density, high performance multiport connectors. Custom and COTS parts are available.
    More
  • High Density Interfaces provide connectivity and maintainability with quick mate/de-mate of multiple cable assemblies. High performance M8 Multi-Port, Mini-Multi-Port (MMP) and BMB 38999 contacts fit standard and custom connector shell designs and provide broadband performance up to 40 GHz. These High Density Interconnect products have been developed to provide extended life and full performance in harsh environments. Sealing features are built into the contact interfaces and connector shells, providing redundant assurance of long-term performance in fielded systems that make them very popular in the military aerospace market.
    More
  • The PN is SV Microwave’s precision version of the type N which offers the user superior electrical characteristics. This series is constructed in stainless steel passivated or gold plated. The PN series meets or exceeds all parameters of MIL- PRE- 39012 Type N connectors designed to this military specification.
    More
  • The PTNC connector is SV Microwave's precision version of the TNC and offers the user superior electrical characteristics. With a frequency range of DC to 15 GHz and tighter machine tolerances, the PTNC series is used in applications such as telecom, base stations, radars, and antennas. The PTNC has a threaded coupling interface, which ensures the connector will not de-couple in vibration-intensive applications.
    More
  • The LP-WBX-N high performance series uses a filter circuit to provide exceptional lightning protection over the 2000-6000MHz frequency band, covering both the unlicensed WiFi bands and several licensed operating bands. Unlike competitive protectors, the white bronze plated construction of the LP-WBX-N series eliminates potential galvanic corrosion issues and provides long life in hostile environments. The fully weatherized housing is sealed to IP65 allowing for outdoor as well as indoor installation.
    More
  • The Times-Protect® LP-GTV-N series is an exceptional broadband DC pass design for lightning protection applications requiring DC power to be supplied to the electronics. These devices exhibit outstanding RF performance with high surge current handling characteristics and cover a broad range of applications requiring up to 150W of RF power handling. Its fully weatherized housing meeting IP67 standard allows for outdoor as well as indoor installation. The N connector designs cover the entire frequency spectrum from DC through 7000MHz.
    More
  • SV Microwave’s QuarterBack® connector line utilizes a quarter turn bayonet style coupling nut with a locking feature for standard SMP/SMPM interfaces. These connectors are ideal for high vibration and test applications that require a large number of mating cycles.
    More
  • SMA is an acronym for SubMiniature version A. Using a threaded interface, 50 Ohm SMA connectors are precision subminiature units that provide excellent electrical performance from DC to 26.5 GHz. These high-performance connectors are compact in size and mechanically have outstanding durability. Built in accordance with MIL-PRF-39012 and CECC 22110/111, SMA connectors can be mated with all connectors that meet these spec mating diameters regardless of manufacturer.
    More
  • SV Microwave offers a complete line of SMP connectors that conform to DSCC 94007, 94008 and MIL-STD-348. The SMP connector was developed to meet an industry need for a smaller high frequency compact design that incorporated ease of use and functionality. The SMP bullet is the heart of this unique design.
    More
  • SV Microwave offers a complete line of SMPM connectors.  The SMPM connector was developed to improve on the application density and operating frequency range of the SMP connector.  The SMPM connector is widely used in high density, high performance applications today.
    More
  • SV's SMPS design is capable of frequencies exceeding 100 GHz. Being 45% smaller than the SMP and 30% smaller then the SMPM, the SMPS is ideal for dense packaging in multiport applications. The SMPS also has a low interface height making it an excellent choice for board-to-board applications using a bullet design. Current configurations include male and female cable connectors, board mount, edge launch and the female bullet. The male interface is available in smooth bore for easy mating or detent for female retention. Directly compatible with the G3PO interface, the SMPS has low VSWR of 1.12 to 50 GHz for the female bullet while allowing for .010” of radial and axial misalignment. The smooth bore design will mate and demate a minimum of 500 cycles and the detent design is capable of 100 cycles minimum.
    More
  • Terminations are used to prevent an RF signal from being reflected back from the end, causing interference. SV offers a broad range of terminations in SMA, 2.92mm, 2.4mm, 1.85mm, SMP, SMPM & SMPS series.
    More
  • Designed as a threaded version of the BNC, the TNC series features screw threads for mating. TNC are miniature, threaded weatherproof units with a constant impedance of 50 Ohms and operate at DC to 11 GHz. As a ruggedized version of the BNC, the TNC features a threaded coupling that offers extra mating stability. TNC connectors are used in many applications including Mil-Aero, instrumentation, and cable assemblies.
    More
  • The Type N connector was developed to satisfy the need for a durable, weatherproof, medium-size RF connector with consistent performance through 11 GHz.
    More
  • SV’s unique connector retention mechanism makes assembly/disassembly a lot easier than competition. The floating SMPM coaxial contacts ensure excellent RF performance in any mating condition. These parts are also designed for side-by-side implementation with VITA 46 hardware and can be cabled to Ø.086 and smaller coaxial cable types. Rear panel interface enables quick disconnect & replacement of card, leading to a significant reduction in Mean-Time-To-Repair (MTTR) when compared to front panel interfaces. Customized configurations available for 67.3 and Commercial Off-The-Shelf (COTS) versions available for 67.1 & 67.2. Go to SV’s Product Search finder on their website to find connectors readily available in distribution.
    More
  • The ZMA connector is a bayonet coupling device. The unique design of this connector provides a high coupling force, which is ideal for extreme vibration applications where insufficient room is available for spring loaded blindmate panels. The ZMA is a quarter-turn coaxial connector that can be mated by hand so that special tooling is not required for proper installation. There are 8 keying arrangements are available to prevent improper mating of assemblies in blind installations. The ZMA connector is designed with electrical performance of 18 GHz, overlapping PTFE dielectrics, and rugged stainless steel body construction appropriate for military applications.
    More
  • LMR cables are high performance coaxial communications cables designed for use in virtually all wireless system applications. The cables are more flexible than corrugated cables and exhibit much lower loss than traditional RG cables. Additional LMR products include high performance connectors in popular interfaces, prep tools, installation tools and accessories.
    More
  • Times Microwave Systems offers a complete line of rugged, specially designed custom cable prep tools. These tools are designed to eliminate or minimize many of the mechanical and electrical variables that play a part in the connector attachment process. In addition to providing much desired control in the field connector attachment process, they offer a considerable time savings and are much safer to use than traditional cable prepping.
    More
  • Times Microwave is the leader in providing high quality EZ style connectors. These non-solder type connectors use silver or gold plated beryllium copper spring contacts for optimal cable contact and offer considerable time savings, increased performance and more reliability than traditional solder-pin connectors. Most of our EZ connectors are available in an "X" version - no braid trim required.
    More
Contact Form